How to Hang a Hammock Chair

Hammock chairs are the ultimate invitation to take a breather, and they can be installed nearly anywhere in and around your home. With the right tools, you can create a hanging oasis outside from a tree branch, or in your own bedroom. Once you know how to properly set up your hammock chair, you'll be able to relax at home in style and comfort.

EditSteps

EditHanging the Chair Outdoors

1. Pick a spot with at least of space from ground to hanging point. The most common spot will be a strong tree branch that can withstand significant weight (at least ). A hardwood tree with healthy horizontal branches will provide the best support. Be sure your location offers of vertical clearance.
   
   • Oak or maple trees are great hardwood trees to use.
   • Check branches for any splitting or weak and worn points near the trunk.
   • You can use a tape measure to figure out the diameter of your tree branch. Between around should hold your hammock chair.
   • Use a meter or yard stick to measure the distance between the ground and the tree branch. It won’t be exact, but it’ll give you a solid estimate.
   • You can also hang your chair on an overhead beam in a gazebo or on your porch.
2. Throw your rope over the branch or beam at least twice. Spread the rope on the branch to distribute weight. This prevents tension from settling at a single point, weakening that spot and increasing the risk of a break later.
   
   • Make sure you have enough rope to accommodate height and the knots you’ll tie. With a rope, you’ll have plenty of slack for height adjustments, and you can cut off the excess.^[1] However, you can probably get by with of rope.
3. Thread the rope ends through the hammock hanging mechanism. Your hammock chair might already have a reinforced loop, either directly on the chair, or at the end of a long rope or cord connected to it. Hold the rope ends in one hand and use the other to grasp the hammock loop. Slide the loop up, keeping the rope taut.^[2]
   
   • The hammock loop should sit right under the branch or beam.
4. Knot the rope below the branch or beam with two half-hitch knots. Wrap the rope line on your left behind the rope line on your right. This forms a small loop beneath the branch. Insert the left rope line through this loop. Pull tight on the left rope. Then repeat, passing the left rope behind the right, then pushing through the new loop created.^[3]
   
   • Pull the knots tight for a strong, tight hold. This ensures the hammock doesn’t fall when used.
   • Use more knots for added security.
5. Test the weight of the chair gradually. Pull on the hammock chair; use plenty of force to test its strength. If it holds, add more weight, like a stack of hefty books or several hand weights. Try to put about on the chair. After that, try lightly sitting on it yourself - or have someone else try. Slowly ease onto the chair until you’re fully seated. If it holds still, the chair is solid.^[4]
   

EditInstalling the Chair Indoors

1. Choose an area with at least of vertical clearance and behind the chair. With of space from floor to ceiling, you’ll ensure there’s room for your chair to hang properly. The space behind the chair offers room for it to spin or sway.^[5]
   
   • You can measure your space with a meter or yard stick. A tape measure also works.
   • Survey the area so the hammock chair isn’t blocking or hitting anything nearby.
2. Use rope for a classic way to hang your hammock chair. Rope is a popular choice, and with indoor use, it’ll last a long time. Rope also offers a beachy aesthetic that adds to the relaxing feeling of the hammock chair.
   
   • Rope requires secure knots. Failing to use them risks damage to your home and could cause injury to whoever is using the hammock chair.^[6]If knots are tricky, chains might be a better choice.
   • Use rope with a working load of at least to ensure it can hold enough weight.
3. Use chains to hang your chair with security. Chains provide enhanced sturdiness for your chair. Depending on the style of the chair or your home, they might not be as nice to look at. But you’ll know that chain won’t fray or break easily.
   
   • Pre-measure your rope or chain so you have enough to attain the desired height. At least of rope will be sufficient for most needs, but if in doubt, it’s better to have more rope than less.
4. Locate a ceiling joist with a stud finder. These tend to be installed apart, so once you’ve found one, you can easily find more should that initial location not work. Use a stud finder, then mark both sides of the joist to find the center where you’ll drill.^[7]
   
   • You can also use a magnet to find the ceiling joist.^[8]
   • If you’re hanging your hammock chair to exposed wooden beams, you can simply install your hooks to the center of the beam.^[9]
5. Use a power drill to drill a pilot hole for the eye screw. The drill bit should be smaller than the eye screw’s width. The pilot hole should be roughly deep and placed at your center mark.
   
   • You’re in the right spot if you see wood shavings on the bit. That means you’ve hit solid wood.^[10]
6. Install the eye screw into the pilot hole. These screws should be long enough to twist at least into the ceiling joists. Insert the eye screw, then turn it clockwise until it’s screwed in tightly. When it’s inserted fully, you shouldn’t see any visible threading on the screw.
   
   • Ideally, the eye screw’s ring should touch the ceiling.
   • Use a screwdriver to help tighten, if needed.
7. Assemble your hanging chair with an S-hook. Link an S-hook to the eye screw. Next, attach your rope to the S-hook, knotting firmly with two half-hitch knots. At the chair’s attachment mechanism, knot again.^[11]
   
   • Chains can be hooked directly onto an S-hook, but you might need another hook or a locking carabiner at the chair’s attachment.
8. Hang your hammock chair by attaching rope directly to eye hooks. Loop your rope through the eye screw. Tie tightly with two or more half-hitch knots. Weave the other end of the rope through the chair’s attachment and use another strong knot or two.
   
9. Test the weight little by little. Pull firmly on the hammock chair. If it holds, add more weight, like a few heavy jugs or some thick books. Next, try lightly sitting on the chair yourself. Keep most of your weight on your legs as you squat over the chair, then slowly ease into the seat until you’re fully supported by it.^[12]
   

EditTips

• Use a freestanding hammock chair stand. They’re useful indoors and outdoors, and relatively simple to set up if you’re having difficulty hanging your chair, or if you’re unable or not allowed to do so. You can also move the stand, so there’s no fussing with hardware or knots.
• If your hammock chair comes with a chair hanging kit, use it. It will include all the pieces needed to properly install and support your chair.

EditReferences

Cite error: <ref> tags exist, but no <references/> tag was found

from How to of the Day http://bit.ly/2UmvAx2
via Peter